Page 1 of 5 123 ... LastLast
Results 1 to 10 of 41

Thread: My 5 point rx7 roll bar pictures

  1. #1
    Owner AutoMods's Avatar
    Join Date
    Jan 2005
    Location
    North Liberty
    Posts
    5,087

    My 5 point rx7 roll bar pictures

    My rx7 infiltrated the MSCA gang for a roll cage installation. They normally don't mess with rice burners.

    Steve and Chris (the twins, or stevo and lorenzo or c-lo or '90 Notch', they have many names) did a great job. Basically started on thursday and car was ready following Wednesday and that was over the memorial weekend.

    Looks like they took their time and made it nice and safe, extra gussets and an extra brace on the drivers side bar on the floor because their was some flex on the drivers floor. Welds look great and they welded to strong areas of the car. They worked around my rear storage bins.

    Drivers side bar is a swing out and that adds some complexity but that looks nice too, swing out bar has a metal pin sleeve welded in the tube for the release pin and the bar is capped for added strength.
    9.875@150mph
    2012 Iowa Manual Shootout Champion, on low boost setting. -Flying Ryan
    "The bitterness of poor quality remains long after the sweetness of low price is forgotten." - Ben Franklin

  2. #2
    Owner AutoMods's Avatar
    Join Date
    Jan 2005
    Location
    North Liberty
    Posts
    5,087
    9.875@150mph
    2012 Iowa Manual Shootout Champion, on low boost setting. -Flying Ryan
    "The bitterness of poor quality remains long after the sweetness of low price is forgotten." - Ben Franklin

  3. #3
    Senior Member sparkles's Avatar
    Join Date
    Jun 2008
    Location
    Forest Moon of Endor
    Posts
    2,893
    Are you happy with that Comp swing out kit? I'm wanting the CAC kit, but at $130 a side, that's a bit of money.

  4. #4
    Senior Member
    Join Date
    May 2005
    Location
    In the BURNOUT BOX
    Posts
    2,206
    Told ya it would be Super nice and fast turn around time.
    2011 IAF/DS Rob Palmer Shootout Winner!
    SOLD!!! 99 Z28 aka "Blackie"
    SOLD!!! FASTEST H/C LS1 IN IOWA!
    JUST A PUMP GAS LS1...
    "EddyB and Son and Daughter Racing"
    New Azz Draggin Grudge Car comming soon!!!
    Comming in "2014" Bimini Blue POS LSX powered notch.
    93 Bimini LSX notch.....aka "BeaterEater"

  5. #5
    Owner AutoMods's Avatar
    Join Date
    Jan 2005
    Location
    North Liberty
    Posts
    5,087
    9.875@150mph
    2012 Iowa Manual Shootout Champion, on low boost setting. -Flying Ryan
    "The bitterness of poor quality remains long after the sweetness of low price is forgotten." - Ben Franklin

  6. #6
    Senior Member snickerlicker's Avatar
    Join Date
    Jul 2004
    Location
    Austin Tx
    Posts
    1,661
    Top notch Lorenzo work again!!!! Looking good!

  7. #7
    IAF Team Member
    Join Date
    May 2005
    Posts
    1,632
    Seems like they are go to guys in Cedar Rapids, love all of the work they have put out.
    ‘47 Willys CJ2A with an SBC

  8. #8
    Senior Member c_mart_28's Avatar
    Join Date
    Jun 2008
    Location
    Urbandale, Iowa
    Posts
    808
    Sweet. I always wanted to cage my fc but never had any reason to.

    Looks good man. Can't.wait to see it running flat out with some tires under it! I didn't get to see it run its best last year.
    Casey
    '03 Mustang

    2010 IAF Manual shootout CHAMP!
    2011 IAF/DS Rob Palmer Shootout Quickest Overall Competitor! (Just Barely..)

  9. #9
    Senior Member
    Join Date
    Jun 2004
    Location
    FINISH LINE BIATCH!!!!!!!!!!!!!!!!
    Posts
    2,144
    Lorenzooo and Stevo always do top notch work...
    CTSV THAT EATS FIRECHICKENS!!!

  10. #10
    Senior Member sparkles's Avatar
    Join Date
    Jun 2008
    Location
    Forest Moon of Endor
    Posts
    2,893

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •