sLoWnStEaDy
11-26-2007, 08:41 PM
Got a new system ordered so figure i would throw my current one up for sale. If i cant get what i want for it, i will just keep it and toss it in one o fmy other cars. subs, amp, power, ground, RCA fuse holder, etc... (no remote wire)
SUBS: (2 brand new, with an extra blown sub you can warranty if you wanna)
I paid about $250 each for them a few years back and they have been sitting in the cases since, finaly hooked them up a couple weeks ago. sell for about $100ea nowa days
• POWFX10W
• 10"
• 1600W power handling
• 800W RMS
• 160-oz magnet
• 2.5" BASV voice coil
• SPL: 91 dB
• Dual 4ohm voice coils
• High-F magnet cover & die-cast aluminum basket with diamond-cut candy-blue finish
• Kevlar-laminated cone
• High-roll Santoprene™ surround
• Black poly-cotton spider with woven tinsel
• Black anodized voice coil former & 1-piece rubber gasket
• Chrome push terminals
AMP: MD Sound (paid $400 a couple months ago, comes with 1 year warranty)
• MD-2629M
• Class D Mono amplifier
• MOSFET POWER SUPPLY
• 1ohm stable
• 2400 Watts maximum output
• 1800W RMS @ 1ohm
• 1000W RMS @ 2ohm
• 800W RMS @ 4ohm
• HEAVY DUTY CHROME PLATED TOP
• HI PASS:50HZ-250HZ
• VARIABLE 18dB BASS BOOST @40HZ
• PWM CONTROLLED DC TO DC SWITCHING POWER SUPPLY
• FREQUENCY RESPONSE: 10-30HZ
• THD:0.02%
• S/N RATIO: 98dB
• FULL SELECTABLE CROSSOVER: HI/LOW/FLAT
• THERMAL PROTECTION
• CIRCUITRY OVERLOAD PROTECTION
• CHROME PLATED RCA CONNECTORS
the box i built myself and is not carpeted yet but will be soon. it is 36X14X14 one chamber (no seperater) which gives it 3.12 cu.ft. air space and is tuned to 30hertz by way of a 4" diameter 9.13" (not exact, cut JUST a tiny bit bigger than 9") long port. right now it is hooked up so it is running at 1ohm... they hit pretty damn hard i must say! The wiring is 4gauge which i was told is the reason i cant run the amp "all out" as there is too mcuh current for teh wire size and that is why the amp goes into "protect" mode when i turn the gain past 50%. Like i said though even at 50% they POUND...
$600
SUBS: (2 brand new, with an extra blown sub you can warranty if you wanna)
I paid about $250 each for them a few years back and they have been sitting in the cases since, finaly hooked them up a couple weeks ago. sell for about $100ea nowa days
• POWFX10W
• 10"
• 1600W power handling
• 800W RMS
• 160-oz magnet
• 2.5" BASV voice coil
• SPL: 91 dB
• Dual 4ohm voice coils
• High-F magnet cover & die-cast aluminum basket with diamond-cut candy-blue finish
• Kevlar-laminated cone
• High-roll Santoprene™ surround
• Black poly-cotton spider with woven tinsel
• Black anodized voice coil former & 1-piece rubber gasket
• Chrome push terminals
AMP: MD Sound (paid $400 a couple months ago, comes with 1 year warranty)
• MD-2629M
• Class D Mono amplifier
• MOSFET POWER SUPPLY
• 1ohm stable
• 2400 Watts maximum output
• 1800W RMS @ 1ohm
• 1000W RMS @ 2ohm
• 800W RMS @ 4ohm
• HEAVY DUTY CHROME PLATED TOP
• HI PASS:50HZ-250HZ
• VARIABLE 18dB BASS BOOST @40HZ
• PWM CONTROLLED DC TO DC SWITCHING POWER SUPPLY
• FREQUENCY RESPONSE: 10-30HZ
• THD:0.02%
• S/N RATIO: 98dB
• FULL SELECTABLE CROSSOVER: HI/LOW/FLAT
• THERMAL PROTECTION
• CIRCUITRY OVERLOAD PROTECTION
• CHROME PLATED RCA CONNECTORS
the box i built myself and is not carpeted yet but will be soon. it is 36X14X14 one chamber (no seperater) which gives it 3.12 cu.ft. air space and is tuned to 30hertz by way of a 4" diameter 9.13" (not exact, cut JUST a tiny bit bigger than 9") long port. right now it is hooked up so it is running at 1ohm... they hit pretty damn hard i must say! The wiring is 4gauge which i was told is the reason i cant run the amp "all out" as there is too mcuh current for teh wire size and that is why the amp goes into "protect" mode when i turn the gain past 50%. Like i said though even at 50% they POUND...
$600