sLoWnStEaDy
11-08-2012, 08:32 PM
never seems to be interest in car audio on here but I figured it is worth a shot. I am already growing bored of this setup and will be going bigger so I this is up for sale.
Pair of RE Audio SEx 10" subwoofers in a "custom" box. ill post sub specs below, the box is .75" MDF with a double front baffle and the subs are flush mounted. it specs out to 2.5ft^3 and is tuned to 34hz via a single 6" aero port. It is sprayed with bedliner. looks pretty good, could be better though. 6" aero is made of schedule 40 PVC and is flared on both ends (obviously). They have been getting about 800w of clean power each for around 2 months now.
Dual Composite 2-piece Cone
Rubatek Foam Surround
Cast Aluminum Basket
Tork-Tite Terminal
3 " 4-layer Aluminum Voice Coil
FEA Optimized Motor Structure
Triple Stack Magnets
Progressive Spiders
Wrap around Rubber Gasket
Mounting Depth - 6.4 inch
Mounting Hole Diameter - 9.3 inch
Overall Diameter - 11 inch
Bolt Hole Circle - 10.1 inch
Motor Width - 7.3 inch
Motor Depth - 3.4 inch
Basket Depth - 2.94 inch
Displacement - 0.14 cu. ft.
Weight - 21 lbs.
Electrical Q Value -Qes: 0.46
Mechanical Q Value -Qms: 4.4
Total Speaker Q Value -Qts: 0.42
Free Air Resonance -Fs: 26.6 Hz
Equivalent Compliance -Vas: 31 liters
One-Way, Linear Excursion -Xmax: 18 mm
Efficiency -SPL 1W/1m: 83.2 dB SPL
Effective Piston Area -Sd: 310 cm^2
DC Resistance -Re: 2.8 ohm
Nominal Impedance -Znom: Dual 4 ohm
Thermal Power Handling -Pe: 600 W
Force Factor -Bl: 17.7
price is $350, they are still in my car so you can hear them if you're interested. Most people think they are loud as hell but I have done 153dB+ so I dont find them all that crazy. Common person would probably be very impressed, LOL. Only selling because I am upgrading
Pair of RE Audio SEx 10" subwoofers in a "custom" box. ill post sub specs below, the box is .75" MDF with a double front baffle and the subs are flush mounted. it specs out to 2.5ft^3 and is tuned to 34hz via a single 6" aero port. It is sprayed with bedliner. looks pretty good, could be better though. 6" aero is made of schedule 40 PVC and is flared on both ends (obviously). They have been getting about 800w of clean power each for around 2 months now.
Dual Composite 2-piece Cone
Rubatek Foam Surround
Cast Aluminum Basket
Tork-Tite Terminal
3 " 4-layer Aluminum Voice Coil
FEA Optimized Motor Structure
Triple Stack Magnets
Progressive Spiders
Wrap around Rubber Gasket
Mounting Depth - 6.4 inch
Mounting Hole Diameter - 9.3 inch
Overall Diameter - 11 inch
Bolt Hole Circle - 10.1 inch
Motor Width - 7.3 inch
Motor Depth - 3.4 inch
Basket Depth - 2.94 inch
Displacement - 0.14 cu. ft.
Weight - 21 lbs.
Electrical Q Value -Qes: 0.46
Mechanical Q Value -Qms: 4.4
Total Speaker Q Value -Qts: 0.42
Free Air Resonance -Fs: 26.6 Hz
Equivalent Compliance -Vas: 31 liters
One-Way, Linear Excursion -Xmax: 18 mm
Efficiency -SPL 1W/1m: 83.2 dB SPL
Effective Piston Area -Sd: 310 cm^2
DC Resistance -Re: 2.8 ohm
Nominal Impedance -Znom: Dual 4 ohm
Thermal Power Handling -Pe: 600 W
Force Factor -Bl: 17.7
price is $350, they are still in my car so you can hear them if you're interested. Most people think they are loud as hell but I have done 153dB+ so I dont find them all that crazy. Common person would probably be very impressed, LOL. Only selling because I am upgrading