PDA

View Full Version : 1986 FC rx7 roller for sale. 375$


e_101
08-24-2010, 02:07 PM
probably should have put this here to begin with instead of misc section...

$375 OBO


Rolling on 5 lug setup and some stock rims with junk tires, all doors fenders and hood included just missing rear/front bumpers. -mostly primed/blocked already.


rear hatch front windshield, engine/body harness is laid out in it but not installed.

Great for Drift/drag. I think its a non turbo chassis but the suspension/drive-train bits that are on it now are from turbo.


Will post pics soom , hit me up at e_101@hotmail.com with questions

I need this gone to make room for my future wife's S14 over the winter:) Ill get a trailer and haul to you if you are close to CR- or even further out if you wanna help with gas.

It has no diff now BTW. car will come with both primer-ed doors, and i was mistaken no harness. I think i have most of it it is just not run in the car. there is one spot that we used bondo on- but id recommend redoing it as i am pretty bad with body work. probably a quick few hour fix for someone who knows what they are doing. car has S5 5 lug spindles all the way around and a freshly painted cleaned sub frame. the rear knuckles were recently sandblasted but are showing some surface rust.


I need this gone to make room for my future wife's S14 over the winter:) Ill get a trailer and haul to you if you are close to CR- or even further out if you wanna help with gas.

It has no diff now BTW. car will come with both primer-ed doors, and i was mistaken no harness. I think i have most of it it is just not run in the car. there is one spot that we used bondo on- but id recommend redoing it as i am pretty bad with body work. probably a quick few hour fix for someone who knows what they are doing. car has S5 5 lug spindles all the way around and a freshly painted cleaned sub frame. the rear knuckles were recently sandblasted but are showing some surface rust.


http://i663.photobucket.com/albums/uu355/ercirel/Skele/DSCN4724.jpg

http://i663.photobucket.com/albums/uu355/ercirel/Skele/DSCN4725.jpg

http://i663.photobucket.com/albums/uu355/ercirel/Skele/DSCN4726.jpg

http://i663.photobucket.com/albums/uu355/ercirel/Skele/DSCN4727.jpg

http://i663.photobucket.com/albums/uu355/ercirel/Skele/DSCN4728.jpg

http://i663.photobucket.com/albums/uu355/ercirel/Skele/DSCN4729.jpg

http://i663.photobucket.com/albums/uu355/ercirel/Skele/DSCN4733.jpg

http://i663.photobucket.com/albums/uu355/ercirel/Skele/DSCN4732.jpg

http://i663.photobucket.com/albums/uu355/ercirel/Skele/DSCN4738.jpg

http://i663.photobucket.com/albums/uu355/ercirel/Skele/DSCN4739.jpg

http://i663.photobucket.com/albums/uu355/ercirel/Skele/DSCN4734.jpg

http://i663.photobucket.com/albums/uu355/ercirel/Skele/DSCN4735.jpg

http://i663.photobucket.com/albums/uu355/ercirel/Skele/DSCN4741.jpg
AutoMods
08-24-2010, 03:11 PM
my fc window's are wobbly, you have a good set of window rails? sunroof is stuck too so may need some parts for that.
e_101
08-25-2010, 09:06 AM
i only have one good sunroof and its going on my fc.

if i end up parting this out the window rails are yours.
Fire Hawk
08-28-2010, 08:55 PM
Do you know what would be needed to drop in a small block chevy into it?
sLoWnStEaDy
08-28-2010, 08:58 PM
Do you know what would be needed to drop in a small block chevy into it?

Easy Peasy....


http://www.grannysspeedshop.com/
e_101
08-30-2010, 07:47 AM
yeah, been done many times- a 5.7 V8 these cars still weigh in well under 3,000 lbs.

Here's another place for swap kits, http://www.hinsonsupercars.com/s-2-mazda-rx7-fc-86-92.aspx

IIRC there is a forum dedicated just to LS swapped Rx-7's
sLoWnStEaDy
08-30-2010, 11:26 AM
yeah, been done many times- a 5.7 V8 these cars still weigh in well under 3,000 lbs.

Here's another place for swap kits, http://www.hinsonsupercars.com/s-2-mazda-rx7-fc-86-92.aspx

IIRC there is a forum dedicated just to LS swapped Rx-7's


forum was v8rx7forum.com but it has been down for quite a while. Also, he said SBC, not LSx, COMPLETELY different swaps obviously. the SBC kit from G.S.S. is DIRT cheap, the basic mount kit is under $400 and the full on, everything you need kti is like $1100~. I went with just the mount kit and used foxbody headers, a stock TII driveshaft with a C4 yolk, and just measured for an aluminum radiator...
e_101
08-30-2010, 02:02 PM
you use a stock TII rear end and axles also right?
sLoWnStEaDy
08-30-2010, 02:07 PM
me personally? Yeah, I use a stock 4.10 LSD from an S4 TII... I have an S5 GTU diff. and axles I am leaving in my old garage if anyone wants them...
AutoMods
08-30-2010, 02:45 PM
norotors.com is the new v8 rx7 forum. last moderator was an ass and wanted to start charging people for pm's and searches. so when people started copying threads over to the new forum, he shut it down to prevent that
sLoWnStEaDy
08-30-2010, 02:48 PM
norotors.com is the new v8 rx7 forum. last moderator was an ass and wanted to start charging people for pm's and searches. so when people started copying threads over to the new forum, he shut it down to prevent that

Good to know!! Thanks!
e_101
08-30-2010, 04:40 PM
me personally? Yeah, I use a stock 4.10 LSD from an S4 TII... I have an S5 GTU diff. and axles I am leaving in my old garage if anyone wants them...


that GTU a 3.90? i may be interested.
sLoWnStEaDy
08-30-2010, 07:33 PM
me personally? Yeah, I use a stock 4.10 LSD from an S4 TII... I have an S5 GTU diff. and axles I am leaving in my old garage if anyone wants them...


that GTU a 3.90? i may be interested.


Pretty sure... I posted it in my other thread. it is at my old garage free for the taking, I will PM you the address...
e_101
08-30-2010, 08:44 PM
i think ive been there, you have the same handle on rx7club don't ya?
sLoWnStEaDy
08-30-2010, 08:53 PM
i think ive been there, you have the same handle on rx7club don't ya?

Yeah... that is me... Keith...
e_101
09-01-2010, 05:04 PM
make an offer people! need it gone
e_101
09-07-2010, 03:03 PM
300$!! common ppl
AutoMods
09-07-2010, 09:47 PM
i need window rails, pass window switch, heater core, could use instrument cluster, don't really want to put a front window in now but mine does have a crack in it and if yours is clean I could grab it
e_101
09-08-2010, 09:05 AM
front windshield is cracked actually. should have mentioned that.

i have an extra cluster and maybe a heater core too.