PDA

View Full Version : New member from muscatine, Well been here a while never post



04-14-2009, 01:39 PM
Hello, My name is Ian I live in muscatine but go to CR quite a bit (hockey)

I have a 91 eagle talon TSI awd
65k miles
new motor .20 over (5k on motor)
I bought the car mid summer last year and only drove it 300 miles then tore her down.

It didn't run when I got it, it had a bad ecu.

So far this is what I did

3 angle valve job
ss valves
BC springs and retainers
3g lifters
comp 100-200 cams
AEM cam gears.
ported ehaust side
Fidanza 2.3 clutch
Fidanza Flywheel
TRE stage 3 trans 10% taller 5th and double syncro 1st
poly mounts
Forced performance race manifold
16g turbo (no ebay junk here)
3" down pipe
Test pipe
2 1/2 inch cat back
megan springs
KYB shocks
Camber kit
Wally 255lph HP pump
Fuel lab FPR with gauge
siemens 750 cc injectors
MBC
Boost gauge
water temp gauge
AEM wideband with gauge
DSMlink v 2.5
Punishment racing FMIC


I know I'm missing something but oh well


This is my 3rd DSM
90 laser rst sold
90 talon tsi awd Blew up 13.9 at cordova with just a 16g
It should be all back together this week and I need to spend some time tuning it but hoping for low to mid 12's

TbTalon94
04-15-2009, 06:16 AM
Very nice mods you have there. There are quite a few DSM guys around here. If you need anything don't hesitate to ask!

Welcome!

-Trevor

Drifte
04-15-2009, 09:02 AM
you want a 4th? You can check out my lucky number 8 in the DSM section. Sounds like a healthy setup.

DustinsDuster
04-15-2009, 02:49 PM
welcome to the board- get some pics up of that runner you got there.

04-15-2009, 09:38 PM
Pics as you requested.

Mind you that these are from the day I picked it up.
I do have one rust spot I have to take care of you will see it in the pics.

This is what it looked like the past sunday. I put the lowering springs and new shocks with the Camber kits on.

http://i249.photobucket.com/albums/gg232/PIMking/talondropped.jpg

Custom fab for my wideband. I dont like the A-Pillar gauge pod (little to ricey for me) but I had to fill it with my boost and water temp gauge so I figured that I'm going to log my wideband with my DSMlink so I put it on the upper din of the radio.
This isn't 100% done but gives you the jist of it.

http://i249.photobucket.com/albums/gg232/PIMking/gaugebezel.jpg

Low miles

http://i249.photobucket.com/albums/gg232/PIMking/red%20talon/redtalon006.jpg

Dusty front view

http://i249.photobucket.com/albums/gg232/PIMking/red%20talon/redtalon008.jpg

Dusty rear view

http://i249.photobucket.com/albums/gg232/PIMking/red%20talon/redtalon001.jpg

Rear bumper damage

http://i249.photobucket.com/albums/gg232/PIMking/red%20talon/redtalon002.jpg

Dusty side view

http://i249.photobucket.com/albums/gg232/PIMking/red%20talon/redtalon003.jpg

Rust Damage (other than the bumper this is all)

http://i249.photobucket.com/albums/gg232/PIMking/red%20talon/redtalon004.jpg

Interior dusty

http://i249.photobucket.com/albums/gg232/PIMking/red%20talon/redtalon005.jpg

Motor Lots have changed reminder this is when I got it.

http://i249.photobucket.com/albums/gg232/PIMking/red%20talon/redtalon009.jpg

After it's first bath

http://i249.photobucket.com/albums/gg232/PIMking/red%20talon/redtalon012.jpg

Nice ass
http://i249.photobucket.com/albums/gg232/PIMking/red%20talon/redtalon015.jpg

Sounds after Cam install and turbo Install (stock exhaust)

http://i249.photobucket.com/albums/gg232/PIMking/red%20talon/th_redtalonvids002.jpg (http://s249.photobucket.com/albums/gg232/PIMking/red%20talon/?action=view&current=redtalonvids002.flv)

sound after a 3" down pipe with test pipe to my 90 talon 2 1/2 inch cat back. I had an idle surge problem that is fixed now (fiav block off)

http://i249.photobucket.com/albums/gg232/PIMking/red%20talon/th_redtalonhead002.jpg (http://s249.photobucket.com/albums/gg232/PIMking/red%20talon/?action=view&current=redtalonhead002.flv)


Let me know what you think 2k there.

Clinical
04-15-2009, 11:11 PM
Very nice, do you ever come to Burlington?

I could swear I've seen that talon around before.

04-16-2009, 07:18 PM
I dont go to burlington often.

I bought my injectors from a guy in burlington though.

I ran into an issue tonight with my FPR I just got around to installing it and then this

http://i249.photobucket.com/albums/gg232/PIMking/talon038.jpg

Drifte
04-20-2009, 09:14 AM
thats for a 2g rail, I have a 2g rail sitting around here somewhere, or get a hold of Import Evolution and see if they will sell you the adapter alone so it fits your 1g rail. Happened to me once to.

04-20-2009, 02:43 PM
I sent that pic to extremepsi.com and Ha sent the right one out for free and overnighted it too.

I do most of my business with extremepsi and MAperformance.